The PRX600 Series represent an evolutionary step in the efficient use of amplifier power, rugged durability and enhanced versatility in a self-powered loudspeaker. Designed from the ground up to perform in the real world of sound reinforcement where challenging audio environments, high ambient noise levels and loud volumes are the norm, the PRX600 Series are built to last a lifetime using our reliable and trustworthy, tour-tested technology. Knowing you can rely on your system to deliver everything you need gives you the freedom to deliver your best. That's performance you can trust.
The PRX635 is a self-powered, lightweight three-way loudspeaker system capable of delivering a very high level of performance over a broad bandwidth.
Maximum SPL 135 db peak
380 mm (15 in) Differential Drive dual voice-coil and magnetic gap, neodymium woofer
165mm (6.5 in) horn loaded midrange transducer
25.4mm (1 in) polymer diaphragm compression driver
1500 Watt (3 x 500 watt) Class-D, Crown digital amplifier
DSP input section with dbx Type IV limiter circuit, crossover, dynamic limiting, component optimization, selectable system EQ
Professional XLR line and 1/4" Mic/Instrument inputs, with loop through
Obsidian DuraFlex coated plywood construction
Large die-cast aluminum handle bar with a fine tuned ergonomic rubber grip for maximum comfort
8 M10 Suspension points and 1 pullback point
Integrated 36mm tripod pole mount socket
System Type : Self-powered 15",
three - way, bass - reflex
Maximum SPL Output : 135 dB peak
Frequency Range (-10 dB) : Flat: 41 Hz - 19 kHz
Boost: 40 Hz - 19 kHz
Frequency Response (+/-3 dB) : Flat: 53 Hz - 18 kHz
Boost: 50 Hz - 18 kHz
Coverage Pattern : 90 degree x 50 degree nominal
Amp Design : Crown Class D
Power Rating : 1500 W ( 3 x 500 )
Dimension (H x W x D) : 921 mm x 424 mm x 413 mm ( 36.29 in x 16.71 in x 16.27 in )
Net Weight : 27.2 kg ( 60 lb )
This speaker is ideally suited to applications where the program material exhibits subtlety and nuance. Perfectly capable of reproducing high fidelity full range sound without a subwoofer, when coupled with extended low frequencies of the PRX618S-XLF, one experiences complete control over the entire audio spectrum. These cabinets can be stand-mounted but do require a large footprint tri-pod type stand. When pole mounting the PRX635 on a subwoofer we highly recommend a pole no longer than 24" (SS3BK-24 or SS4BK-24) to ensure stability and safety. As with all the full-range PRX600 Series systems two EQ selections can be used to optimize the system for the program material and/or environment. The input section also accommodates either Line or Mic/Instrument level inputs.
The PRX635 is a self-powered, lightweight three-way loudspeaker system capable of delivering a very high level of performance over a broad bandwidth. The PRX635 is comprised of one 380 mm (15 in) 265F Differential Drive woofer, a 165 mm (6.5 in) 195H horn-loaded 90 Degrees by 50 Degrees mid-range and a 2414H 25.4 mm (1 in) annular polymer diaphragm, neodymium compression driver mounted to a 90 Degrees by 50 Degrees horn, all driven by a 1500 watt (3 x 500) Audio Class-D power amplifier. A propriety DSP chip is at the core of a fully featured input section, providing user selectable system EQ, protection, input sensitivity selection, cross-over functionality, dynamic limiting and discrete component optimization.
The amplifier input panel offers XLR or 1/4 inch jack compatibility and a sensitivity switch provides extra flexibility, making it possible to connect literally any sound source without using a mixer. Signal present and overload lights indicate the system status and assist in setting the optimum level, via the level control knob.
All PRX600 cabinets are built from a combination of 25mm (on the top and bottom for added rigidity) and 18mm, strong, light-weight poplar plywood made structurally sound with tongue and groove joints. All PRX600 Series cabinets are protected by JBL's tour proven DuraFlex finish. Grilles are made from dent-resistant 16 gauge steel and handles are made from light-weight glass-filled nylon for added strength and durability. All M10 suspension points are constructed from 14 gauge steel and have been tested with a yield-strength of 1000 lbs. each.
Special note: The PRX635 should be pole-mounted on a PRX 600 subwoofer using a pole no longer than 24" in length. (SS3-BK24 or SS4-BK24)
There are currently no videos for this product.
There are currently no related items for this product.
FOR SUPPORT WITH YOUR PRODUCT CONTACT: